A Macro-Distinct Element Model (M-DEM) for simulating the in-plane cyclic behavior of URM structures. Malomo, D. & DeJong, M. J. Engineering Structures, 2021. Computational expense;Distinct element modeling;Experimental damage;Hysteretic behavior;Out-of-plane failures;Shear failure mechanisms;Strain-softening models;Unreinforced masonry;Paper abstract bibtex In this work, a new Macro-Distinct Element Model (M-DEM) for the analysis of the in-plane behavior of unreinforced masonry (URM) structures, aimed at combining the efficiency of simplified approaches with the accuracy of discontinuum-based micro-modeling methods, is presented and validated through comparison against a number of both experimental and numerical tests on URM components. In the M-DEM framework, Finite Element (FE) homogenized macro-blocks are connected by discrete spring interfaces, whose layout is determined a priori as a function of the masonry texture. In-plane diagonal and sliding shear failure mechanisms, as well as flexural damage, are accounted for by the discrete spring interfaces. Meanwhile, a new methodology to simulate crushing, which makes use of a strain-softening model originally conceived for modeling concrete failure, is proposed and calibrated against small-scale tests on masonry samples. The strategy is to simulate shear/tension failure in the block interfaces and compression failure within the FE macro-blocks, while discretizing to allow the possibility of simulating out-of-plane failure modes. Using the M-DEM, the observed experimental damage and the hysteretic behavior of various reduced-scale URM specimens, subjected to shear-compression cyclic loading, were satisfactorily reproduced numerically. The capabilities of the M-DEM to predict the influence of the bond pattern on the monotonic behavior laterally-loaded URM piers were also scrutinized through comparison with standard micro-modeling outcomes, focusing on potential differences concerning both accuracy and computational expense. Finally, given the encouraging results obtained, the proposed approach was extended to the simulation of the in-plane cyclic response of a full-scale URM façade. Although the model marginally underestimated the energy dissipation in the first test phases, a good agreement was obtained in terms of peak and residual base shear capacity, initial in-plane stiffness and its progressive deterioration, governing failure mechanisms and final crack pattern, whilst simultaneously keeping computational costs within acceptable limits.
© 2020 Elsevier Ltd
@article{20204509448962 ,
language = {English},
copyright = {Compilation and indexing terms, Copyright 2023 Elsevier Inc.},
copyright = {Compendex},
title = {A Macro-Distinct Element Model (M-DEM) for simulating the in-plane cyclic behavior of URM structures},
journal = {Engineering Structures},
author = {Malomo, Daniele and DeJong, Matthew J.},
volume = {227},
year = {2021},
issn = {01410296},
abstract = {In this work, a new Macro-Distinct Element Model (M-DEM) for the analysis of the in-plane behavior of unreinforced masonry (URM) structures, aimed at combining the efficiency of simplified approaches with the accuracy of discontinuum-based micro-modeling methods, is presented and validated through comparison against a number of both experimental and numerical tests on URM components. In the M-DEM framework, Finite Element (FE) homogenized macro-blocks are connected by discrete spring interfaces, whose layout is determined a priori as a function of the masonry texture. In-plane diagonal and sliding shear failure mechanisms, as well as flexural damage, are accounted for by the discrete spring interfaces. Meanwhile, a new methodology to simulate crushing, which makes use of a strain-softening model originally conceived for modeling concrete failure, is proposed and calibrated against small-scale tests on masonry samples. The strategy is to simulate shear/tension failure in the block interfaces and compression failure within the FE macro-blocks, while discretizing to allow the possibility of simulating out-of-plane failure modes. Using the M-DEM, the observed experimental damage and the hysteretic behavior of various reduced-scale URM specimens, subjected to shear-compression cyclic loading, were satisfactorily reproduced numerically. The capabilities of the M-DEM to predict the influence of the bond pattern on the monotonic behavior laterally-loaded URM piers were also scrutinized through comparison with standard micro-modeling outcomes, focusing on potential differences concerning both accuracy and computational expense. Finally, given the encouraging results obtained, the proposed approach was extended to the simulation of the in-plane cyclic response of a full-scale URM façade. Although the model marginally underestimated the energy dissipation in the first test phases, a good agreement was obtained in terms of peak and residual base shear capacity, initial in-plane stiffness and its progressive deterioration, governing failure mechanisms and final crack pattern, whilst simultaneously keeping computational costs within acceptable limits.<br/> © 2020 Elsevier Ltd},
key = {Deterioration},
keywords = {Textures;Failure (mechanical);Stiffness;Energy dissipation;Hysteresis;Masonry materials;Numerical methods;},
note = {Computational expense;Distinct element modeling;Experimental damage;Hysteretic behavior;Out-of-plane failures;Shear failure mechanisms;Strain-softening models;Unreinforced masonry;},
URL = {http://dx.doi.org/10.1016/j.engstruct.2020.111428},
}
Downloads: 0
{"_id":"J5wLkbDQiJv266RiM","bibbaseid":"malomo-dejong-amacrodistinctelementmodelmdemforsimulatingtheinplanecyclicbehaviorofurmstructures-2021","author_short":["Malomo, D.","DeJong, M. J."],"bibdata":{"bibtype":"article","type":"article","language":"English","copyright":"Compendex","title":"A Macro-Distinct Element Model (M-DEM) for simulating the in-plane cyclic behavior of URM structures","journal":"Engineering Structures","author":[{"propositions":[],"lastnames":["Malomo"],"firstnames":["Daniele"],"suffixes":[]},{"propositions":[],"lastnames":["DeJong"],"firstnames":["Matthew","J."],"suffixes":[]}],"volume":"227","year":"2021","issn":"01410296","abstract":"In this work, a new Macro-Distinct Element Model (M-DEM) for the analysis of the in-plane behavior of unreinforced masonry (URM) structures, aimed at combining the efficiency of simplified approaches with the accuracy of discontinuum-based micro-modeling methods, is presented and validated through comparison against a number of both experimental and numerical tests on URM components. In the M-DEM framework, Finite Element (FE) homogenized macro-blocks are connected by discrete spring interfaces, whose layout is determined a priori as a function of the masonry texture. In-plane diagonal and sliding shear failure mechanisms, as well as flexural damage, are accounted for by the discrete spring interfaces. Meanwhile, a new methodology to simulate crushing, which makes use of a strain-softening model originally conceived for modeling concrete failure, is proposed and calibrated against small-scale tests on masonry samples. The strategy is to simulate shear/tension failure in the block interfaces and compression failure within the FE macro-blocks, while discretizing to allow the possibility of simulating out-of-plane failure modes. Using the M-DEM, the observed experimental damage and the hysteretic behavior of various reduced-scale URM specimens, subjected to shear-compression cyclic loading, were satisfactorily reproduced numerically. The capabilities of the M-DEM to predict the influence of the bond pattern on the monotonic behavior laterally-loaded URM piers were also scrutinized through comparison with standard micro-modeling outcomes, focusing on potential differences concerning both accuracy and computational expense. Finally, given the encouraging results obtained, the proposed approach was extended to the simulation of the in-plane cyclic response of a full-scale URM façade. Although the model marginally underestimated the energy dissipation in the first test phases, a good agreement was obtained in terms of peak and residual base shear capacity, initial in-plane stiffness and its progressive deterioration, governing failure mechanisms and final crack pattern, whilst simultaneously keeping computational costs within acceptable limits.<br/> © 2020 Elsevier Ltd","key":"20204509448962","keywords":"Textures;Failure (mechanical);Stiffness;Energy dissipation;Hysteresis;Masonry materials;Numerical methods;","note":"Computational expense;Distinct element modeling;Experimental damage;Hysteretic behavior;Out-of-plane failures;Shear failure mechanisms;Strain-softening models;Unreinforced masonry;","url":"http://dx.doi.org/10.1016/j.engstruct.2020.111428","bibtex":"@article{20204509448962 ,\nlanguage = {English},\ncopyright = {Compilation and indexing terms, Copyright 2023 Elsevier Inc.},\ncopyright = {Compendex},\ntitle = {A Macro-Distinct Element Model (M-DEM) for simulating the in-plane cyclic behavior of URM structures},\njournal = {Engineering Structures},\nauthor = {Malomo, Daniele and DeJong, Matthew J.},\nvolume = {227},\nyear = {2021},\nissn = {01410296},\nabstract = {In this work, a new Macro-Distinct Element Model (M-DEM) for the analysis of the in-plane behavior of unreinforced masonry (URM) structures, aimed at combining the efficiency of simplified approaches with the accuracy of discontinuum-based micro-modeling methods, is presented and validated through comparison against a number of both experimental and numerical tests on URM components. In the M-DEM framework, Finite Element (FE) homogenized macro-blocks are connected by discrete spring interfaces, whose layout is determined a priori as a function of the masonry texture. In-plane diagonal and sliding shear failure mechanisms, as well as flexural damage, are accounted for by the discrete spring interfaces. Meanwhile, a new methodology to simulate crushing, which makes use of a strain-softening model originally conceived for modeling concrete failure, is proposed and calibrated against small-scale tests on masonry samples. The strategy is to simulate shear/tension failure in the block interfaces and compression failure within the FE macro-blocks, while discretizing to allow the possibility of simulating out-of-plane failure modes. Using the M-DEM, the observed experimental damage and the hysteretic behavior of various reduced-scale URM specimens, subjected to shear-compression cyclic loading, were satisfactorily reproduced numerically. The capabilities of the M-DEM to predict the influence of the bond pattern on the monotonic behavior laterally-loaded URM piers were also scrutinized through comparison with standard micro-modeling outcomes, focusing on potential differences concerning both accuracy and computational expense. Finally, given the encouraging results obtained, the proposed approach was extended to the simulation of the in-plane cyclic response of a full-scale URM façade. Although the model marginally underestimated the energy dissipation in the first test phases, a good agreement was obtained in terms of peak and residual base shear capacity, initial in-plane stiffness and its progressive deterioration, governing failure mechanisms and final crack pattern, whilst simultaneously keeping computational costs within acceptable limits.<br/> © 2020 Elsevier Ltd},\nkey = {Deterioration},\nkeywords = {Textures;Failure (mechanical);Stiffness;Energy dissipation;Hysteresis;Masonry materials;Numerical methods;},\nnote = {Computational expense;Distinct element modeling;Experimental damage;Hysteretic behavior;Out-of-plane failures;Shear failure mechanisms;Strain-softening models;Unreinforced masonry;},\nURL = {http://dx.doi.org/10.1016/j.engstruct.2020.111428},\n} \n\n\n","author_short":["Malomo, D.","DeJong, M. J."],"id":"20204509448962","bibbaseid":"malomo-dejong-amacrodistinctelementmodelmdemforsimulatingtheinplanecyclicbehaviorofurmstructures-2021","role":"author","urls":{"Paper":"http://dx.doi.org/10.1016/j.engstruct.2020.111428"},"keyword":["Textures;Failure (mechanical);Stiffness;Energy dissipation;Hysteresis;Masonry materials;Numerical methods;"],"metadata":{"authorlinks":{}}},"bibtype":"article","biburl":"https://bibbase.org/network/files/m3A3cns49MKmeRzt5","dataSources":["iK69edT4peeXELcwY","6Aw5QAtT2yLJ3d2JP","qBPxBjrzghRQ4Wzbf","EnwwBMFxopKkypo2f","8uWbXNBCDiEboMj8h"],"keywords":["textures;failure (mechanical);stiffness;energy dissipation;hysteresis;masonry materials;numerical methods;"],"search_terms":["macro","distinct","element","model","dem","simulating","plane","cyclic","behavior","urm","structures","malomo","dejong"],"title":"A Macro-Distinct Element Model (M-DEM) for simulating the in-plane cyclic behavior of URM structures","year":2021}